Problem Set 4

See the Guidelines. I will post on ASULearn answers to select questions I receive via messaging there or in office hours!

Problem 1:  3.1 #43 Determinant(A); will compute the determinant in Maple, and A:=RandomMatrix(5); will give you a 5x5 matrix with random integer entries.

Problem 2:  2.8 #12. Additional Instructions:
Part A: First solve for Nul A, include the definition of Null A in your explanation/annotated reasoning, and then give p as directed.
Part B: Next solve for Col A as follows: Reduce A, circle the pivots and provide the pivot columns of A (not reduced A) as the basis for the Col A. Then give q as directed.
Part C: Find an equation that the vectors in Col A satisfy as follows: Set up and solve the augmented matrix for the system Ax=Vector([b1,b2,b3,b4,b5]]) and apply GaussianElimination(Augmented); in Maple. Are there any inconsistent parts (like [0 0 0 0 0 combination of bs]) to set equal to 0?
Part D: What is the geometry of Col A using part B? Choose one from [point, line, plane, volume, hyperplane, entire space] and explain why in your annotations.

Problem 3:  5.6 #12 with the following directions:
Part A: In Maple compute the eigenvalues and eigenvectors using fractions in A instead of decimals using Eigenvectors(A);.
Part B: Write out the eigenvector decomposition for the system.
Part C: Do the populations grow, die off, stabilize, or exibit some other behavior in the longrun for most starting conditions? Explain why.
Part D: For most starting positions, what is the yearly rate in the long term (growth rate, die off rate, or stability rate). Explain where your number came from.
Part E: For most starting positions, what is the eventual ratio the system tends to? Explain where your ratio came from.
Part F: Sketch (by-hand) a trajectory diagram for the system, by graphing the two eigenvectors, picking a starting point in the first quadrant different from the eigenvectors, and sketching what happens over time, like in the examples in the glossary on ASULearn (for trajectory).
Part G: In Maple input the original matrix using decimals and execute Eigenvectors(A);. Are the eigenvectors approximately on the same lines the corresponding ones with fractions were? Check each eigenvector and show work/reasoning.
Part H: Are the eigenvectors exactly on the same lines? (Hint: look at the last digits of the x and y values in the eigenvector corresponding to the larger eigenvalue).


Problem 4:  Rotation matrices in R2   Recall that the general rotation matrix which rotates vectors in the counterclockwise direction by angle theta is given by
M:=Matrix([[cos(theta),-sin(theta)],[sin(theta),cos(theta)]]);
  Part A:   Apply the Eigenvalues(M); command (Eigenvalues, not Eigenvectors here) in Maple or solve for the eigenvalues by-hand. Notice that there are real eigenvalues for certain values of theta only. What are these values of theta and what eigenvalues do they produce? Show work/reasoning. (Recall that I = the square root of negative one does not exist as a real number and that cos(theta) is less than or equal to 1 always, and you'll want this in your annotate.)
  Part B: For each real eigenvalue, find a basis for the corresponding eigenspace (Pi is the correct way to express pi in Maple - you can use comamnds like Eigenvectors(Matrix([[cos(Pi/2),-sin(Pi/2)],[sin(Pi/2),cos(Pi/2)]])); in Maple, or by-hand otherwise.
  Part C:   Use only a geometric explanation to explain why most rotation matrices have no eigenvalues or eigenvectors (ie scaling along the same line through the origin). Address the definition of eigenvalues/eigenvectors in your response as well as how the rotation angle connects to the definition in this case.
A Review of Various Maple Commands:
> with(LinearAlgebra): with(plots):
> A:=Matrix([[-1,2,1,-1],[2,4,-7,-8],[4,7,-3,3]]);
> ReducedRowEchelonForm(A);
> GaussianElimination(A); (only for augmented matrices with unknown variables like k or a, b, c in the augmented matrix)
> Transpose(A);
> ConditionNumber(A); (only for square matrices)
> Determinant(A);
> Eigenvalues(A);
> Eigenvectors(A);
> evalf(Eigenvectors(A));
> Vector([1,2,3]);
> B:=MatrixInverse(A);
> A.B;
> A+B;
> B-A;
> 3*A;
> A^3;
> evalf(M)
> spacecurve({[4*t,7*t,3*t,t=0..1],[-1*t,2*t,6*t,t=0..1]},color=red, thickness=2); plot vectors as line segments in R3 (columns of matrices) to show whether the the columns are in the same plane, etc.
> implicitplot({2*x+4*y-2,5*x-3*y-1}, x=-1..1, y=-1..1);
> display(a,b,c);
> implicitplot3d({x+2*y+3*z-3,2*x-y-4*z-1,x+y+z-2},x=-4..4,y=-4..4,z=-4..4); plot equations of planes in R^3 (rows of augmented matrices) to look at the geometry of the intersection of the rows (ie 3 planes intersect in a point, a line, a plane, or no common points)